How to make a shampoo-free window tint solution for baby


[ad_1]

Cars can be a valuable asset. And if the opportunity arises, many people would like to secure their car for as long as possible.

Americans now maintain their cars longer than ever, according to a report by Cars and Drivers magazine. The average American can keep a car for 10.5 years.

Window tinting gives cars durability as the film permanently blocks harsh UV rays which can damage the skin and discolor the upholstery of the car.

However, tinted windows in your car do more than protect the interior of your vehicle. A properly installed window tint can also protect you and your property from prying eyes.

Most window tint solutions are made with baby shampoo. Baby shampoo lubricates the tint film, ensuring the film does not stick to itself when applied.

So what happens when you want to put on your tint film and you don’t have baby shampoo? Perhaps you would like to satisfy your curiosity by trying other solutions.

Here are the steps for making a shampoo-free window tint solution for baby.

How to make a shampoo-free window tint solution for baby

Step 1: Get a pan:

Fill this saucepan or pot halfway with water.

Step # 2: Add your favorite dish soap:

In the pot or saucepan, add 14 teaspoons of your washing-up liquid in place of the baby shampoo. Soap is a degreaser; it helps remove tar, dirt and oil.

You can also use tinted slime. There are no particles in the tinted slime and it is biodegradable. It is suitable for application on interior surfaces.

Step 3: Add one or two tablespoons of alcohol:

Alcohol is a drying agent. It allows the water and soap molecules to evaporate quickly, leaving the surface clean and flawless.

Step 4: Mix thoroughly:

Using a spoon, stir the soapy solution to obtain a homogeneous mixture.

Step 5: Prepare your spray bottle:

Remove the sprayer from a spray bottle and set it aside.

Step # 6: Fill the spray bottle with the mixture:

To avoid spilling the soap mixture, use a funnel to pour it into the spray bottle. Then reattach the sprayer to the bottle. Make sure to secure the sprayer to the spray bottle.

Now you have your window tint solution. Although not always necessary, your mixture should produce a white foamy effect when spraying the dye solution with the bubbles.

How would you like to tint your car window?

Many car owners wish to tint their windows to protect the interior of their vehicle from the heat of the sun and harmful UV rays. However, not everyone knows how to properly install window tint film.

Before tinting, you should check your state’s policies on car window tinting to avoid getting into trouble with the authorities. Some states in the United States, such as Pennsylvania, require 70% light transmission for tinting car windows.

Although window tinting can take time, the steps below will show you how to tint your windows with a few essential tools.

Step 1: Clean the window glass:

Scrub the window glass thoroughly to make sure it is free of dirt. Also, it would help if you were working in a clean and dust free environment. Dust particles can make your glass look like a bubble if you’re not careful.

In addition, you should remove any car stickers or adhesives and wipe the surface thoroughly with a damp cloth. For a thorough cleaning, use a mixture of lukewarm water and detergent in a spray bottle.

Some people use ammonia to clean glass surfaces, but it is not recommended. The ammonia will make your window tint purple when you’re done.

Then wipe off the soapy water with a clean, dry cloth. Then wipe down the gaskets and clean as much as possible between the gasket and the glass.

Step # 2: Separate the tint film layer from the liner:

The tint has a coating that you can peel off just before adhering to the window, similar to a sticker. Put a piece of masking tape on each side of the edge of the film. Make sure that half of the tape is adhered to the film and the other half is over the edge.

Then spray enough soapy water on the exterior window. The water will allow the tint film to stick firmly but temporarily.

Step 3: Spread the tint film on your car window:

Unroll your tinted film with the liner facing you. Use scissors or a razor blade to cut off the edges of the excess film.

Secure the film properly and make sure the bottom edge protrudes about half to one quarter of the top of the window seal from the inside of the car. Make sure you have enough tint film to cover the edges of the window all around.

Step 4: Spray the outer protective film with soapy water:

This step is necessary for the realignment of your tint film. Be sure to spray the exterior siding with soapy water. It helps your film to stick perfectly to the window and erase the creases. You can trim the edges of the excess film with a razor blade.

Step # 5: Eliminate All Air and Bubbles:

Flatten all of the film outside the window by pressing from top to bottom. You will see the line where air or bubbles are still stuck in the film if you tap on it.

You can use a heat gun along the bottom of the window to make sure everything is dry. After flattening the overlapping strokes, use a blade to cut off the excess film on the top edges of the car. However, it would be better to open the car door before cutting.

When cutting, gently hold and tap the blade at a low angle. Do not press too hard to avoid accidental scratches or damage to the glass. You don’t want to waste your efforts, so cut with caution.

Step # 6: Prepare the interior car window:

At this point, you should spray the inner glass with the soapy water you prepared previously. Then clean the windows thoroughly with a soft towel and dry with a low-lint cloth. Remember to clean between window seals.

Step # 7: Separate the two layers of the tint film:

Just as you know, this window tint works like a sticker. Now it’s time to peel off the removable diaper. This removable layer adheres to the tint film to keep the adhesive strong. You can start by removing the top half of the diaper using two pieces of duct tape.

While holding the tape on the film, pull it up and away from the window. Then slowly separate the two layers to expose the adhesive. Avoid touching the sticky layer as much as possible.

You can now spray the exposed layer with clean water. The water makes the tint easier to glide over, allowing you to perfectly line your window edge with the top edge of the tint.

Step # 8: Stick the adhesive side of the tint film to the wet glass inside the car:

Place the film on the window where it should be and gently hold it in place. Leave about â…› of an inch between the glass top and the tint film so that the window tint does not roll into the tracks where it could fall.

Now your car is about to have that tinted appearance.

Step 9: Smooth out the folds and position the film on the glass:

Remove trapped air bubbles by pressing down the middle and bottom of the window. At this time, the water will flow behind the window film. Just wipe it off with a cloth.

Fold back the bottom edge of the dye film to prevent residual dust from adhering to the film.

Step # 10: Yeh! You have successfully tinted your car window:

However, allow the tinted glass to dry completely. You have to wait seven days for the tint to dry and harden completely before lowering the window.

If you roll down your car window when the tint on the window is not yet dry, the tint may peel off. Then, unfortunately, you may have to start all over again.

When is the best time to tint your windows?

The best time to tint windows is in early spring and late fall. This is because temperatures are warmer and humidity levels are lower in most parts of the country during these two seasons.

Please note that things are very different in summer and winter. Hot summer weather will speed up the curing process, but high humidity will make it more difficult to apply the tint effectively.

On the other hand, the curing time is much longer in winter due to the cold weather. Therefore, before rolling down the windows, you must be very careful to confirm that the stain has hardened well during this season.

Conclusion

The safety benefits of placing window film on your car cannot be overstated. Window tinting offers more than aesthetic value. It also provides long term protection for you and your vehicle.

However, to benefit from this protection, you must install your the window tint with a high quality dye solution, mostly with baby shampoo. However, you can use your favorite tinted slime or dish soap as a substitute.

The soap perfectly removes grease, tar, dirt and paints, while the tint mud is particle-free and biodegradable.

[ad_2]

Comments are closed.